Shower installation Cleburne TX done right the first time

When you need shower installation Cleburne TX homeowners can count on, our team handles everything from tear-out to final caulk line. We install walk-in showers, replace failing pans, and convert tubs into low-threshold showers that fit how you actually live.

Serving cleburne and nearby areas.

How big is the shower job?

Convert

Tub comes out, drain gets reworked, new pan and valve go in.

  1. 1. Swap Same-size replacement, existing drain lines up, standard pan and valve.
  2. 2. Convert Tub comes out, drain gets reworked, new pan and valve go in.
  3. 3. Custom Tile walls, moved drain, glass enclosure, planned in writing first.
  • 30Services from one local team
  • 20Areas served around cleburne
  • Camera firstWe inspect the drain before quoting
  • Flood testPan holds water 24 hours before tile

What's included in a shower installation

Every shower install we quote covers the tear-out, the rough plumbing, the pan, the walls, the trim, and the cleanup.

Shower Installation in cleburne : plumber is connecting the hot and cold water lines to a new shower valve body within a

Work order

Shower Installation
  • Tear-out and haul-away: We remove the old tub or shower, cut out the surround or tile, and haul everything to the curb. Floors and doorways get protected with drop cloths and plastic sheeting before the first tool comes out of the truck.
  • Drain inspection and re-slope: We run a pipe camera inspection down the drain and confirm the slope is at least a quarter-inch per foot. If the drain is cast iron or undersized, we cut it out and couple in 2-inch PVC with a shielded fitting to meet code.
  • New pan and liner: The pan sets on a sloped mortar bed with a PVC liner underneath and a flood test that holds water for 24 hours before tile or wall panels go down. That test is the difference between a shower that lasts 20 years and one that leaks in two.
  • Valve and trim installation: We install a pressure-balanced or thermostatic valve set at 120 degrees to prevent scalding, then set the trim, showerhead, and handle. Moen, Delta, and Kohler cartridges are all stocked locally, so replacement parts are easy to find later.
  • Walls, glass, and caulk: Acrylic panels, solid surface, or tile go up over a waterproofed substrate. We seal the grout in wet zones, caulk every joint with a mold-resistant silicone, and hang the glass or curtain rod as the last step.
  • Cleanup and walkthrough: We haul off all debris, wipe down the bathroom, and walk you through the shutoff locations, valve settings, and surface care.

What the first visit covers

First visit

We measure the opening, camera the drain, check the subfloor, and explain what the install involves.

Shower installation at your home

We install showers in houses across Cleburne and Johnson County.

  • Tub to shower

    Tub comes out, drain gets upgraded, walk-in goes in.

  • Failed pan swap

    Cracked pan replaced with a sloped mortar bed.

  • Aging in place

    Low threshold, blocking for grab bars, handheld head.

  • Master remodel

    Tile walls, linear drain, glass, new valve.

Sink Installation in cleburne : plumber is carefully lowering a new stainless steel kitchen sink into the countertop cutout

Shower installation for Cleburne businesses

We handle shower and bath work for commercial properties and multi-unit buildings.

  • Rental units

    Same-day pan and valve replacement for occupied units.

  • Small hotels

    Guest bath shower replacement scheduled around occupancy.

  • Gyms and shops

    Locker room shower pans and valve upgrades.

What shower installation Cleburne TX really involves

A shower is the one fixture you use every day and the one you never see behind the wall. Installing it right the first time costs less than fixing it twice.

Shower installation Cleburne TX is the full process of removing an old tub or shower, correcting the drain and supply plumbing behind the wall, setting a new pan or tile base, and tying in a valve, trim, and glass or curtain enclosure. It is not a drop-in liner job. We open the wall, check for rot, verify the drain slope, and make sure the valve body sits at the right depth for the finished wall thickness. If the existing drain is cast iron or the subfloor is soft, we fix that before anything gets set. A proper install starts with the rough-in, not the tile.

Most Cleburne homes built before 1985 still have original cast iron drains and 2-inch shower pans that were never meant for today's flow rates. Add North Texas clay soil that shifts with every wet-dry cycle, and you get cracked pans, loose tile, and slow drains that show up as ceiling stains downstairs. If you've been searching for shower installation near me Cleburne TX and getting bids that skip the drain inspection, that's the bid to walk away from. We camera the line first, then quote the work.

Garbage Disposal Repair in cleburne : plumber is using an Allen wrench to manually clear a jam in a garbage disposal unit
What it is
Tear-out, new pan, valve, walls, and trim.
When it helps
Cracked pan, low pressure, or a tub you can't step over.
What you get
A watertight shower that passes inspection.

How our shower install day runs

Every job follows the same sequence, whether it's a one-day acrylic swap or a four-day tile build.

  1. Walkthrough and measure

    We arrive, pull the old trim, and measure the rough opening, drain location, and stud spacing.

  2. Tear-out and inspection

    We remove the old tub or shower, haul it out, and open the wall to the studs.

  3. Rough-in plumbing

    New PEX supply lines get run and crimped, the drain gets re-sloped to a quarter-inch per foot, and the valve body gets blocked and strapped at the correct depth.

  4. Pan, walls, and trim

    The pan goes down on mortar, the liner gets flood-tested, and the walls go up.

  5. Cleanup and walkthrough

    We haul off every scrap, wipe the bathroom down, and walk you through the shutoffs, the valve settings, and how to care for the surfaces.

Tools and methods we use on every install

Each method answers a different question. Together they leave very little to guess.

We run a camera down the drain before quoting so we know if there's root intrusion, scale, or a collapsed section. Finding it now beats finding it after the pan is set.

Used to make secure, code-compliant connections on new PEX supply lines. Crimp rings get checked with a go/no-go gauge so a loose joint never gets buried in the wall.

For copper pipe connections where the existing supply lines are copper. We use a heat shield behind the studs to protect framing and insulation from the flame.

We check static and dynamic water pressure before and after the install. High pressure above 80 PSI gets a regulator so the new valve and supply lines aren't stressed.

For clearing soap scum, hair, and light buildup in the shower branch line before the new pan goes down. Keeps the drain flowing the way it should from day one.

When Cleburne homeowners call us for a shower

  • Aging parent needs a safer step-in after a fall or surgery, and the hall bath still has a 17-inch tub wall.

    We convert the tub to a walk-in shower with a 2-inch threshold, add blocking for grab bars, and install a pressure-balanced valve…

    Homes
  • Master bath remodel where the 1990s acrylic surround has yellowed and the pan flexes underfoot.

    We tear out the old surround and pan, inspect the drain, and build a new tiled shower with a linear drain and…

    Homes
  • Rental property where the shower pan failed and the tenant is without a usable shower.

    We confirm the leak with a pipe camera inspection, then install a standard 60-inch acrylic pan and Delta valve kit from stock.

    Businesses
  • New construction or addition where the rough-in is in but the shower has never been finished.

    We set the pan, waterproof the walls, install the valve and trim, and tie the drain into the existing line with the…

    Homes

How shower installation runs in Cleburne

Cleburne sits on expansive clay soil that swells when it's wet and shrinks when it's dry, and that movement shows up in bathroom plumbing. Shower drains shift, pans crack, and supply line joints work loose over time.

  • Cleburne Historic District

    Homes here date to the 1920s and 1930s with original cast iron drains and tight bathroom footprints. We plan for custom pan sizes and drain relocation more often in this area.

  • Lake Pat Cleburne

    Higher water pressure is common near the lake, and some homes have had previous remodels with mixed pipe materials. We pressure-test and camera before quoting.

  • Chisholm Trail

    Newer construction with clean PEX rough-ins and standard 60-inch openings. Most jobs here are straight swaps or upgrades to a larger walk-in pan.

Plumbing in cleburne : close-up of a pressure gauge on a water testing manifold, showing a steady reading during a leak test
  • Cleburne Historic District
  • Lake Pat Cleburne
  • Chisholm Trail
  • Henderson Street Corridor

From problem to finished result.

Slide to compare the photo with an illustrative inspection view. It is generated from the photo, not a measurement.

Plumbing in cleburne : plumber is interacting with a male homeowner in a kitchen, pointing to a newly installed faucet withPhoto
  • 1948 cast iron tub to walk-in shower

    Before: A 1948 home near the Historic District had the original cast iron tub, a drain that was half clogged with scale, and a cracked closet bend leaking into the crawlspace. The bathroom was 5 feet by 8 feet with a window over the tub.

    After: We pulled the tub, replaced the closet bend, and installed a 60-inch walk-in pan with a 2-inch threshold and a Moen pressure-balanced valve. The window got a framed surround and a waterproofed substrate. Job took three days including the flood test.

  • Failed pan in a 1980s rental unit

    Before: A rental near North Cleburne had a shower pan that had cracked and was leaking into the unit below. The tenant was showering at a neighbor's house. The existing pan was a thin fiberglass unit set directly on the subfloor with no liner.

    After: We cut out the old pan, sistered two soft joists, and set a new acrylic pan on a mortar bed with a PVC liner. A Delta valve kit went in while the wall was open. Same-day completion, tenant back in the shower by 6 p.m.

  • Tub-to-shower conversion with drain upgrade

    Before: A homeowner near Buffalo Creek wanted to age in place but the hall bath had a 17-inch tub wall and a 1.5-inch cast iron drain. Two previous bids quoted the conversion without addressing the drain size, which would have backed up within weeks.

    After: We cut the old drain out, ran 2-inch PVC with the correct slope, and built a 2-inch threshold walk-in with blocking for grab bars and a handheld showerhead. The valve was set at 120 degrees. Four days total including inspection.

Shower problems we fix before they spread

Most shower failures start small and stay hidden until the damage is expensive.

Ask about yours

  • Cracked shower pan leaking into the ceiling below

    A cracked pan can push 5 to 10 gallons a day into the subfloor and joists.

  • Tub-to-shower conversion blocked by undersized drain

    Older Cleburne homes often have 1.5-inch cast iron tub drains.

  • Low shower pressure from corroded galvanized supply lines

    Galvanized pipe rusts from the inside out.

  • Mold and mildew behind failing caulk and grout

    Black mildew behind caulk means moisture is getting into the wall cavity.

Why a new shower pays off

A shower is the hardest-working fixture in the house.

No more leaks downstairs

A failed shower pan can push 5 to 10 gallons a day into your subfloor before you notice.

Safer step-in height

Walk in shower installation Cleburne gives you a threshold as low as 2 inches instead of a 17-inch tub wall.

Lower water bills

A WaterSense-labeled showerhead caps flow at 2.0 gallons per minute. Swap out a 1990s 5.

Easy to clean, hard to stain

Acrylic and solid-surface walls wipe down in under a minute with no grout lines to scrub.

What you get in writing

Clear records you can keep and share.

  • Written scope

    Pan size, valve model, wall material, and price.

  • Drain camera photos

    What the line looks like before we quote.

  • Flood test record

    Confirmation the pan held water 24 hours.

Before work starts

A plan in writing

Ask for a written scope

16 years of shower work in Johnson County

Cleburne Trailcrest Plumbing has been installing showers since 2010, which means 16 years of opening walls in this town and seeing what's actually behind them.

Plumbing in cleburne : high-angle shot looking down at a plumber working under a kitchen sink, with a basin wrench in hand

Drain slope

We check for a quarter-inch per foot so water exits instead of pooling.

Subfloor condition

Soft spots mean rot, and rot means framing repair before the pan sets.

Valve depth

The valve body has to sit at the right depth for the finished wall thickness.

Is your Cleburne address covered?

Type your ZIP code or town to check. If you're not listed, call and ask.

cleburne ZIP codes

  • 76033
  • 76031

What Cleburne homeowners say

Our 1948 house had the original cast iron tub and a drain that was half clogged with scale. The crew from Cleburne Trailcrest pulled it, showed me the cracked closet bend on camera, and had a new walk-in pan and Moen valve in by the second afternoon. They flood-tested the pan overnight and let me watch. No leaks, no surprises on the bill.
Marcus T.Homeowner, Cleburne Historic District
I needed a low-threshold shower for my mother after her hip surgery. They measured the joists, told me honestly that a curbless pan wouldn't work without reframing, and built a 2-inch curb instead. Added blocking for grab bars while the wall was open. Three days start to finish, and they cleaned up better than I expected.
Dana R.Homeowner, Lake Pat Cleburne
I manage four rentals and had a shower pan fail at one of them on a Friday. They came out, confirmed the leak with a camera, and had a standard acrylic pan and Delta valve installed the same day. Tenant was back in the shower by evening. I've used them on two more units since.
Raymond K.Landlord, North Cleburne

Shower installation questions we hear every week

Short answers for the first few minutes. The team can cover the rest.

Still have a question?

Describe what you are seeing and we will point you to the right next step.

(682) 468-2111

The biggest cost drivers are wall material, whether the drain has to move, and whether we find rot or a bad subfloor during tear-out. We give you a written number before we start, and if we find something behind the wall, we show you photos and price it before we touch it.

A standard acrylic shower replacement takes one day, usually 6 to 8 hours. A tub-to-shower conversion with a new pan and valve runs two days. Custom tile with a mortar bed and flood test takes three to four days because the pan has to cure and the liner has to hold water for 24 hours before tile. We schedule the work so you're not without a shower any longer than necessary.

Yes. Walk in shower installation Cleburne is one of our most requested jobs, especially for aging-in-place remodels and anyone who wants a low 2-inch threshold instead of a tub wall. We can build a curbless design if the floor framing allows it, add blocking for grab bars, and install a linear drain so the floor slopes in one direction. We'll tell you honestly if your joist layout won't support a curbless pan.

We convert tubs to showers regularly, and it's usually a two-day job. The tub comes out, the drain gets reworked to a shower drain with the correct slope, and the supply lines get repositioned for the new valve height. One thing to plan for: the old tub drain is often 1.5-inch cast iron, and we bring it up to 2-inch PVC to meet code. That's a good time to camera the line and check for root intrusion.

Get your shower installation Cleburne TX quote

(682) 468-2111

We'll walk your bathroom, camera the drain, and give you a written price before any work starts. Call Cleburne Trailcrest Plumbing and let's get your new shower scheduled.

Contact Cleburne Trailcrest Plumbing

Call us at (682) 468-2111 or email info@cleburnetrailcrestplumbing.com. We answer the phone Monday through Friday, 8 a.m. to 6 p.m., and we run emergency calls after hours. If you leave a message, we call back the same day. Tell us what you're seeing and we'll tell you what it likely is and when we can get there.

Call now(682) 468-2111