Faucet installation Cleburne TX done right the first time

When you need faucet installation Cleburne TX homeowners trust, we handle the whole job: shutoff, removal, supply lines, and a leak-free finish. Whether it is a kitchen faucet installation Cleburne TX project or a bathroom upgrade, we work on Moen, Delta, and Kohler fixtures daily.

Serving cleburne and nearby areas.

How big is the job?

Valve work

Faucet plus new shutoff valves or supply lines.

  1. 1. Simple swap One faucet, existing shutoffs work, standard sink.
  2. 2. Valve work Faucet plus new shutoff valves or supply lines.
  3. 3. Full rebuild Faucet, valves, drain assembly, and disposal connection.
  • 30Services from one local team
  • 20Areas served around cleburne
  • Pressure testEvery connection checked
  • New linesSupply lines replaced

What our faucet installation includes

Every faucet install includes the basics: removal of the old fixture, installation of the new one, new supply lines, and a full pressure test.

Faucet Installation in cleburne : plumber is securing the mounting nuts of a new outdoor hose bib to the exterior wall of a

Work order

Faucet Installation
  • Old faucet removal: We disconnect the supply lines, remove the mounting nuts, and lift out the old faucet. The sink deck gets scraped clean of old putty and mineral buildup.
  • New faucet installation: We set the new faucet with fresh plumber's putty or silicone, feed the supply lines through the deck, and tighten the mounting hardware from underneath with a basin wrench.
  • New supply lines: We replace the supply lines as part of the install. Old lines can crack when they are reconnected, so new ones protect your cabinet from a slow leak.
  • Pressure test and leak check: We open the shutoff valves slowly and check every connection with a dry paper towel. Any weep gets fixed before we move on to testing hot and cold flow.
  • Drain and sprayer check: We test the drain for leaks and check the sprayer for proper flow. If the P-trap or drain flange is corroded, we can replace it during the same visit.

What the first visit covers

First visit

We inspect the shutoff valves and supply lines, remove the old faucet, and install the new one.

Faucet installation at your home

We install kitchen, bathroom, and utility faucets in Cleburne homes.

  • Kitchen faucet

    Pull-down, pull-out, or standard.

  • Bathroom faucet

    Single or double handle.

  • Utility sink

    Laundry and garage sinks.

  • Bar sink

    Small fixtures and prep sinks.

Tankless Water Heater Repair in cleburne : plumber is cleaning the internal filter of a tankless water heater, with the

Faucet installation for businesses

We install faucets in commercial kitchens, restrooms, and break rooms.

  • Restaurant kitchens

    Pre-rinse and utility faucets.

  • Office restrooms

    Metering and sensor faucets.

  • Retail break rooms

    Standard kitchen faucets.

Faucet installation Cleburne TX: what the job really involves

A faucet installed correctly lasts a decade. One installed with old supply lines and a worn drain can leak within weeks. We do the whole job so you are not fixing it twice.

Faucet installation Cleburne TX is the removal of an old or failing fixture and the precise fitting of a new one, including supply lines, drain connections, and seals. We shut off the angle stops, disconnect the old faucet, clean the mounting surface, and set the new unit with new washers and Teflon tape. On a typical kitchen sink, we also check the garbage disposal flange and the P-trap for corrosion while everything is apart.

Most calls we get in Cleburne start with a dripping faucet that has worn out its cartridge or a remodel where the old fixture no longer matches. If you have been searching for faucet installation near me Cleburne TX, we can usually get to you the same day or next morning. We carry common Moen and Delta cartridges on the truck, so a simple swap does not turn into a second appointment.

Water Softener Installation in cleburne : plumber is carefully adding bags of water softener salt into the brine tank of a
What it is
Removing an old faucet and installing a new one.
When it helps
Drips, leaks, or a remodel.
What you get
A tested, leak-free faucet.

Our faucet installation process

Every job follows the same five steps, whether it is a bathroom faucet installation Cleburne or a full kitchen upgrade.

  1. Shutoff and inspect

    We turn off the angle stops and open the faucet to bleed pressure. Then we inspect the supply lines, shutoff valves, and cabinet floor for existing leaks.

  2. Remove the old fixture

    We disconnect the supply lines, loosen the mounting nuts, and lift the old faucet out. The sink deck gets scraped clean of old plumber's putty and mineral buildup.

  3. Set and seal the new faucet

    We apply fresh plumber's putty or silicone to the new faucet base, feed the supply lines through the deck holes, and tighten the mounting hardware from underneath.

  4. Connect and pressure test

    New supply lines get threaded on with Teflon tape and hand-tightened, then snugged a quarter turn with a wrench.

  5. Test and clean up

    We run hot and cold water for two minutes, check the drain for leaks, and test the sprayer. Then we wipe down the sink, cabinet, and floor.

Tools and methods we use

Each method answers a different question. Together they leave very little to guess.

Reaches the mounting nuts behind the sink bowl without scratching the finish or skinning knuckles.

Loosens stubborn supply line nuts and shutoff valves that have seized over time.

Checks water pressure at the faucet after installation to confirm it is within normal range.

Seals threaded connections on supply lines and shutoff valves to prevent slow leaks.

Crimps PEX pipe connections when we replace a section of supply line during the install.

When to schedule a faucet installation

  • You are remodeling the kitchen and want a new faucet to match the sink and countertop.

    We remove the old faucet, install the new one, and connect the sprayer and disposal.

    Homes
  • Your bathroom faucet is 15 years old and the finish is peeling or the handle is hard to turn.

    We install a new bathroom faucet with fresh supply lines and a new drain assembly if needed.

    Homes
  • You bought a faucet online and need it installed, but you are not sure it will fit.

    We check the hole spread, deck thickness, and supply line length before we start.

    Homes
  • A rental property needs a new faucet between tenants and you need it done fast.

    We schedule the install around your turnover window, install a customer-supplied or stock faucet, and test every connection.

    Businesses

How faucet installation works in Cleburne

Cleburne sits in Johnson County, where the water is hard enough to shorten faucet cartridge life. That means a faucet that drips after five years is often a cartridge issue, not a fixture defect.

  • Downtown Cleburne

    Older homes here often have original shutoff valves that seize up. We replace them during the faucet install to prevent future problems.

  • Buffalo Creek

    Newer construction with PEX pipe. Faucet installs are straightforward, but we still check for proper supply line length and drain alignment.

  • Cleburne Historic District

    Historic homes may have copper pipe with soldered joints. We inspect for corrosion and replace any brittle sections before installing the new faucet.

Pipe Replacement in cleburne : plumber is joining new copper pipes together with a press tool in a utility area, replacing
  • Downtown Cleburne
  • Buffalo Creek
  • Cleburne Historic District
  • Lake Pat Cleburne

From problem to finished result.

Slide to compare the photo with an illustrative inspection view. It is generated from the photo, not a measurement.

Repiping in cleburne : plumber is carefully securing new PVC drain lines within a framed wall cavity of a house being repipedPhoto
  • Kitchen faucet swap in Buffalo Creek

    Before: A 12-year-old kitchen faucet with a leaking base and a sprayer that dribbled. The shutoff valves were frozen, and the supply lines were brittle. The cabinet floor had a small water stain.

    After: We installed a new Moen kitchen faucet, replaced both shutoff valves and supply lines, and sealed the base. The sprayer works at full pressure, and the cabinet is dry. Total time: two hours.

  • Bathroom faucet upgrade in Downtown Cleburne

    Before: A bathroom faucet with peeling chrome and a handle that needed two hands to turn. The drain flange was corroded and the P-trap leaked slightly.

    After: We installed a new Delta bathroom faucet, replaced the drain assembly and P-trap, and tested hot and cold flow. The handle turns with one finger, and the drain seals tight. Total time: 75 minutes.

  • Utility sink faucet replacement in North Cleburne

    Before: A laundry room faucet that had been dripping for months. The threads on the old supply lines were stripped, and the shutoff valve would not close fully.

    After: We installed a new utility faucet with new supply lines and a quarter-turn shutoff valve. The drip stopped, and the valve now shuts off completely. Total time: one hour.

Faucet problems we solve in Cleburne

A bad faucet wastes water, stains the sink, and can damage the cabinet below.

Ask about yours

  • Dripping faucet that will not stop

    A steady drip wastes 3,000 gallons a year and stains the sink basin.

  • Leaking supply line under the sink

    A slow leak rots the cabinet floor and can seep into the subfloor. By the time you smell mildew, the damage is often already done.

  • Frozen shutoff valve

    A valve that will not turn means you cannot shut off water during an emergency.

  • Corroded drain flange or P-trap

    A rusted drain flange can leak into the cabinet and cause the sink to drain slowly. It also makes the new faucet look out of place.

Why homeowners call us for faucet work

A new faucet is only as good as the install behind it.

Stop the drip for good

A worn cartridge can waste 3,000 gallons a year.

Protect your cabinets

A slow leak under the sink rots the cabinet floor before you notice.

Match the fixture to your sink

Not every faucet fits every sink deck. We measure the hole spread, deck thickness, and reach before we recommend anything.

Handle the whole swap

We remove the old faucet, install the new one, reconnect the sprayer, and test hot and cold.

What you receive

Clear records you can keep and share.

  • Install summary

    What we installed and tested.

  • Parts list

    Supply lines and valves replaced.

  • Care notes

    How to maintain the finish.

Before work starts

A plan in writing

Ask for a written scope

16 years of faucet work in Johnson County

Cleburne Trailcrest Plumbing has been installing faucets since 2010.

Faucet Repair in cleburne : plumber is tightening a loose faucet base onto a bathroom sink, working from underneath with a

Shutoff condition

We turn the valve to see if it closes fully. If it does not, we replace it.

Supply line age

We check for cracks or corrosion. Brittle lines get replaced.

Drain alignment

We dry-fit the P-trap to make sure it lines up without stress.

Is your Cleburne address covered?

Type your ZIP code or town to check. If you're not listed, call and ask.

cleburne ZIP codes

  • 76033
  • 76031

What Cleburne customers say

Our kitchen faucet had been dripping for months. The team from Cleburne Trailcrest came out, replaced the faucet and both supply lines, and tested everything. They also noticed the shutoff valve was frozen and replaced it. The sink has been dry ever since. Fair price and no mess left behind.
Karen M.Homeowner, Downtown Cleburne
I bought a Delta faucet online and needed it installed. They checked the box for missing parts, installed it, and even adjusted the sprayer hose. Took about an hour and a half. They showed me the pressure test and cleaned up the cabinet. I will call them again for the bathroom faucet.
David R.Homeowner, Buffalo Creek
We manage several rental units and needed bathroom faucets replaced in two of them. Cleburne Trailcrest Plumbing scheduled both on the same day, installed customer-supplied fixtures, and tested each one. They left the units clean and ready for tenants. Good communication and no callbacks.
Linda S.Property Manager, Cleburne Historic District

Faucet installation questions we hear in Cleburne

Short answers for the first few minutes. The team can cover the rest.

Still have a question?

Describe what you are seeing and we will point you to the right next step.

(682) 468-2111

A basic bathroom faucet with existing shutoffs is on the low end. Kitchen faucets with a sprayer, a garbage disposal, or frozen shutoff valves push toward the higher end.

A standard bathroom faucet takes 45 to 75 minutes. A kitchen faucet with a sprayer and disposal typically runs 90 minutes to two hours. If we have to replace shutoff valves or cut out a corroded drain flange, add 30 to 45 minutes. We give you a time estimate before we start.

Yes. We install customer-supplied faucets regularly. We ask that you have the faucet on site and unboxed so we can check for missing parts before we start. If the fixture is the wrong size or missing a mounting kit, we will tell you right away so you can exchange it.

We install both. Kitchen faucet installation Cleburne TX jobs are our most common call, followed by bathroom faucets and utility sink faucets. We also handle bar sinks, laundry sinks, and outdoor hose bibbs. If it has a supply line and a drain, we can install it.

Schedule your faucet installation Cleburne TX today

(682) 468-2111

Call Cleburne Trailcrest Plumbing for a faucet installation Cleburne TX homeowners recommend. We give you a price before we start, show up when we say we will, and test every connection.

Contact Cleburne Trailcrest Plumbing

Call us at (682) 468-2111 or email info@cleburnetrailcrestplumbing.com. We answer the phone Monday through Friday, 8 a.m. to 6 p.m., and we run emergency calls after hours. If you leave a message, we call back the same day. Tell us what you're seeing and we'll tell you what it likely is and when we can get there.

Call now(682) 468-2111